Modular gaming table
Re: Modular gaming table
I've had quite a productive day today, so...........Next update.
I laid my foundation boards out in the intended formation and then placed another layer of foam on 4 of them like this
I then drew a rough hill shape on them. Making sure that where each one met the next, would be exactly 17" from the centre. By doing this I can ensure that whatever configuration I use for the boards each game, the sides of every hill will match all the others and line up to create 1 large hill as shown or 2 half hills along the sides or ends or 4 quarter hills in the corners.
Using this tool (I think its called a dry-wall saw) I cut the shape out of the foam
I then placed some off-cuts of foam on top to create another layer to the hill. I marked out a rough shape as before and made sure that each piece met the next at exactly 9 1/2" from the centre for the same reason as listed above. Then cut the shape out with the same saw as before.
Next I inserted some cocktail sticks into the foundation boards squirted a lattice pattern of PVA glue onto the underside of the hill base pieces, making sure to put glue right up to the edge as well. I then pressed the hill piece down onto the cocktail sticks and down flush to the foundation. It took a few attempts with each board to get the sides lined up correctly but it is easy to reposition them as required.
Once all of them were glued I stacked them on top of each other, placed a piece of card over the top and weighted them with 6 house bricks. I will take and post photos of them once the glue has dried overnight. Once dry I will create sloped sides for the hills by cutting some sections away and adding pieces of off-cuts, as well as the cork I showed in an earlier post as rocky outcroppings. These will then be blended together using polyfilla (spackle) to fill gaps and smooth joints.
Photos of stacked and dried boards as promised
The remaining 2 foundation boards are going to be marshy lowlands so I marked out some patches on them that will be low points in the fields and therefore be the watery marsh patches. I then took a large screwdriver with a rounded handle (as shown, with my hand for scale) and used the handle to hammer the foam down in the areas I had marked in order to create depressions in the surface.
Once the board is textured, painted and flocked these recesses will have water effects poured into them to create a moist and marshy look rather than large pools of swamp like terrain.
Hopefully this covers things well enough but I will answer any questions you may have as well as I can.
I laid my foundation boards out in the intended formation and then placed another layer of foam on 4 of them like this
I then drew a rough hill shape on them. Making sure that where each one met the next, would be exactly 17" from the centre. By doing this I can ensure that whatever configuration I use for the boards each game, the sides of every hill will match all the others and line up to create 1 large hill as shown or 2 half hills along the sides or ends or 4 quarter hills in the corners.
Using this tool (I think its called a dry-wall saw) I cut the shape out of the foam
I then placed some off-cuts of foam on top to create another layer to the hill. I marked out a rough shape as before and made sure that each piece met the next at exactly 9 1/2" from the centre for the same reason as listed above. Then cut the shape out with the same saw as before.
Next I inserted some cocktail sticks into the foundation boards squirted a lattice pattern of PVA glue onto the underside of the hill base pieces, making sure to put glue right up to the edge as well. I then pressed the hill piece down onto the cocktail sticks and down flush to the foundation. It took a few attempts with each board to get the sides lined up correctly but it is easy to reposition them as required.
Once all of them were glued I stacked them on top of each other, placed a piece of card over the top and weighted them with 6 house bricks. I will take and post photos of them once the glue has dried overnight. Once dry I will create sloped sides for the hills by cutting some sections away and adding pieces of off-cuts, as well as the cork I showed in an earlier post as rocky outcroppings. These will then be blended together using polyfilla (spackle) to fill gaps and smooth joints.
Photos of stacked and dried boards as promised
The remaining 2 foundation boards are going to be marshy lowlands so I marked out some patches on them that will be low points in the fields and therefore be the watery marsh patches. I then took a large screwdriver with a rounded handle (as shown, with my hand for scale) and used the handle to hammer the foam down in the areas I had marked in order to create depressions in the surface.
Once the board is textured, painted and flocked these recesses will have water effects poured into them to create a moist and marshy look rather than large pools of swamp like terrain.
Hopefully this covers things well enough but I will answer any questions you may have as well as I can.
Last edited by AndyP on Thu Apr 25, 2013 6:51 am, edited 1 time in total.
As I always say. At the end of the day.................it goes dark
- JLLongshore
- Posts: 85
- Joined: Wed Mar 13, 2013 10:15 am
Re: Modular gaming table
Thank you for sharing, very interesting, looking forward to final.
Re: Modular gaming table
I like the idea of using the screwdriver handle to press down into the foam, consider that idea stolen
Aka Dave
Re: Modular gaming table
Funkychef wrote:I like the idea of using the screwdriver handle to press down into the foam, consider that idea stolen
Yeah, I didn't fancy melting it as some people do, just because of the fumes. I tried scraping some off the surface with a spoon but it tore the surface too much so thought hammering it down would be the best option. Worked quite well and once it is textured, flocked and wetted the uneven surface won't be an issue.
As I always say. At the end of the day.................it goes dark
- zedmeister
- Posts: 131
- Joined: Mon Feb 25, 2013 2:26 pm
- Location: Mercia, UK
- Contact:
Re: Modular gaming table
This is really inspiring me to start making my own boards. Any chance you could go through a bit more detail on how you sealed and strengthened the outside edges of the boards.
Next payday, I think I'll be order some of these: http://www.antenocitisworkshop.com/600x ... -tile.html
Next payday, I think I'll be order some of these: http://www.antenocitisworkshop.com/600x ... -tile.html
Re: Modular gaming table
+1 for Zed's request about sealing the edges info
Also, i was meaning to ask, are you planning on beveling your hillf to a slope? or leaving them as a drop off at the edge?
Also, i was meaning to ask, are you planning on beveling your hillf to a slope? or leaving them as a drop off at the edge?
Aka Dave
Re: Modular gaming table
zedmeister wrote:This is really inspiring me to start making my own boards. Any chance you could go through a bit more detail on how you sealed and strengthened the outside edges of the boards.
Next payday, I think I'll be order some of these: http://www.antenocitisworkshop.com/600x ... -tile.html
If you are ordering the boards from antenocitis, you won't need to do as much as I had to with mine, as the sides will all be level and perfect 90 degree angles. I cut mine out of larger pieces of insulation boards with a retractable knife and the foam forces the blade to bend slightly and causes unevenness in the surface. Once they were mounted on MDF I then ended up layering polyfilla on in a thick layer and using a set square lined up along the underside to scrape off the excess, leaving me with a vertical and uniform edge. If you mount them on 1/4" MDF like I did (you can get that in sheets from any DIY store and most will be able to cut it into 60cm x 60cm squares for you, B&Q did mine). I recommend using "No Nails" to glue the foam to the MDF but use a plastic spreader to cover the whole MDF with a thin coat then stack the boards in a tower and place something heavy on top to press them all down (put some card on before the weight to protect the surface of the foam). There are 2 options you could use to strengthen the sides of those, either "No Nails" or PVA glue. I think "No Nails" will be the quickest option as it goes on as a thick line and you can use a plastic spreader to smear it into a thin layer all around the sides (think smoothing peanut butter over toast) and it won't soak into the foam. So long as it goes on as a thin, almost transparent layer, it shouldn't crack as it dries out and will leave a very hard shell. PVA will be easier to get a thin smooth layer as you can leave it undiluted and just paint it on with a 2" brush like any house paint. It will soak into the foam however and so will need 2-3 coats, allowing each to dry thoroughly over night before applying the next. Both methods should give you a hard shell like finish to the edges it just depends whether you prefer simple but long-winded or quicker but slightly more technical. Hope this helps
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Funkychef wrote:+1 for Zed's request about sealing the edges info
Also, i was meaning to ask, are you planning on beveling your hillf to a slope? or leaving them as a drop off at the edge?
I will create sloping sides by removing the foam at an angle in some places and adding in scrap pieces in others. This will then be smoothed over with polyfilla and pieces of cork bark added as rocky outcroppings.
As I always say. At the end of the day.................it goes dark
- Rob Lane
- Site Admin
- Posts: 3716
- Joined: Fri Feb 15, 2013 2:46 pm
- Location: Warsop Vale, Nottinghamshire
- Contact:
Re: Modular gaming table
Superb work Andy! Looking forward to seeing the result.
Cheers
Rob
Cheers
Rob
Mierce Miniatures
https://mierce-miniatures.com
https://mierce-miniatures.com
Re: Modular gaming table
Another quick update. I have added the scrap pieces of various sizes to create the lower slopes on one piece. I could have just cut the slopes out of the full size piece in the first place but this way gave me more flexibility in shaping it and creating a more natural uneven look when its finished. I am going to have cork bark at the joining point on each board this will be more forgiving when matching the joints up than if the joining point was a sloping hill. All the pieces were glued into place using a hot-glue gun as shown.
I have also started work on some trees, both coniferous and deciduous, here are the WIPs
I have also started work on some trees, both coniferous and deciduous, here are the WIPs
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
I think you need to do a tree tutorial Andy. Your scenery is looking great!
Wyrd bið ful aræd
Re: Modular gaming table
AndyS wrote:I think you need to do a tree tutorial Andy. Your scenery is looking great!
I can do one if people want me too, but there are tonnes of them on youtube. That's where I looked for tips. If people want me to do one then let me know and I will post a new thread on here.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Next piece of the board sculpted
Also, this is what I use to carve the foam into slopes and chunks-a regular kitchen knife.
However, always cut away from yourself
DOH!!
Also, this is what I use to carve the foam into slopes and chunks-a regular kitchen knife.
However, always cut away from yourself
DOH!!
As I always say. At the end of the day.................it goes dark
- zedmeister
- Posts: 131
- Joined: Mon Feb 25, 2013 2:26 pm
- Location: Mercia, UK
- Contact:
Re: Modular gaming table
Oooo, you bugger! Knife slipped?
Re: Modular gaming table
Is it that obvious?
The perils of DIY.
The perils of DIY.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Next update. I finished off the first level of the hill on all 4 pieces using the same method as described earlier all the way around.
Then, using the same method of PVA glue and cocktail sticks as I did for the first layer (see previous post) I glued the second layer of hill on top and carved the slopes in the same way, gluing more bark on as rocky outcrops in various places.
At this point I can demonstrate why a modular set up like this is better than a single 6x4 piece. Simply put.......variety
Next job is smoothing over the cracks and places where the foam meets the bark with polyfilla and reinforcing the joining sides of each piece with a thin layer of "no nails" as described in my previous posts. Once that is done I will texture the whole board with ballast and small rocks before starting to paint it. As always feel free to ask questions. Next update coming soon.
Then, using the same method of PVA glue and cocktail sticks as I did for the first layer (see previous post) I glued the second layer of hill on top and carved the slopes in the same way, gluing more bark on as rocky outcrops in various places.
At this point I can demonstrate why a modular set up like this is better than a single 6x4 piece. Simply put.......variety
Next job is smoothing over the cracks and places where the foam meets the bark with polyfilla and reinforcing the joining sides of each piece with a thin layer of "no nails" as described in my previous posts. Once that is done I will texture the whole board with ballast and small rocks before starting to paint it. As always feel free to ask questions. Next update coming soon.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Looks great indeed.
Re: Modular gaming table
Great looking stuff. I've always used a saw or something more like a breaking to chop that sort of foam
Can't wait to see more
Can't wait to see more
Re: Modular gaming table
That's supposed to say say something like a bread knife
Re: Modular gaming table
Looking great
When i opened the page initially it was half over one the pics, so this is what greeted me on the screen
Which just looked sooooo wrong
When i opened the page initially it was half over one the pics, so this is what greeted me on the screen
Which just looked sooooo wrong
Re: Modular gaming table
Oh..That's just wrong
Re: Modular gaming table
I assure you this thread will stay as PG rated. I'll do an 18 certificate only by popular demand
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
And why do we have a forum-member who has an online-shop with all secret weapon washes?!?!?! Damn you Valiant...placed an order
Re: Modular gaming table
Rick_Boer wrote:And why do we have a forum-member who has an online-shop with all secret weapon washes?!?!?! Damn you Valiant...placed an order
Well since your a fellow forum member i'll throw in some freebies.
Re: Modular gaming table
Polyfilla time. Using a spreader such as this one....
I applied a covering of polyfilla all over the slopes to cover any joints and small gaps. In the areas around the bark and other awkward sections it was easier to apply the filla with my fingers.
Once dry this will be sanded to remove all of the lumpy and spiky bits on the slopes. More pics coming soon.
I applied a covering of polyfilla all over the slopes to cover any joints and small gaps. In the areas around the bark and other awkward sections it was easier to apply the filla with my fingers.
Once dry this will be sanded to remove all of the lumpy and spiky bits on the slopes. More pics coming soon.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Any updates on this? It is looking awesome. I am really thinking about duplicating some of your ideas. Thanks for posting all of the pictures.
-Quuids
-Quuids
Re: Modular gaming table
I have done some more work on this and will be posting pics in the next day or so.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Great news, thanks Andy
Re: Modular gaming table
Next step turned out to be very messy. Taking some medium grit sandpaper I set about smoothing the filla. Turning this,
Into this,
The dust created by this procedure was ridiculous and coated every inch of my garage in a film of white powder. I reccommend using a respirator mask while doing this.
Once all the boards, and my garage, were hoovered off I could start gluing the ballast on top. Using a 2" household paint brush I applied a generous coat of homemade scenic cement (50/50 mix of PVA glue and water with 2 drops of washing up liquid) to small sections of each board, pouring the ballast on top while the cement was still wet. Best results came from starting at the base level and coating roughly half the area with glue then adding the ballast in quite a thick layer, approx 1/4" thick leaving an inch or so of the glue exposed at the edge where the next lot of glue and ballast would go down. Then coated the 2nd half of the base level with glue making sure to overlap onto the inch you left exposed and liberally covering with more ballast. The first level of the hill was done the same way but spreading down the hill slopes as well. The top level could be done in one hit as it has a smaller surface area to cover. All 4 hill boards were done the same way. The lowland boards were easier just doing each one a quarter at a time using the same method. Each board was balanced on a house brick on the floor so that any overruns of glue down the sides would not glue them to the floor.
The middle photo above was of a board done in a different way to what I described but was the first board I did and I found the described method to be better.
The ballast was applied using a small jar like this,
When finished they look like this,
Once it was all dry I took another 2" paint brush and gently brushed off the excess ballast back into the container. The boards now need sealing to hold down any fine dust and grit so it doesn't cause a problem when I paint it. For this I use the same scenic cement mixture as before but need it to be delivered via a fine mist spray. Woodland scenics sell a dedicated sprayer for this,
It is crap!
So I bought a cheap spray bottle from a discount shop,
This is also crap!
Both of these only manage a single jet spray not a mist and they drip all over the place. I then found this in B&Q,
This works perfectly. Pump up the pressure with the built in pump, hold the trigger and get a nice even mist no problem and no drips. Really recommend this.
Once all 6 boards had a coat of sealant they were left to dry on bricks again for 2 days and nights and are now ready for undercoating.
That's it for now. As always, questions welcome.
Into this,
The dust created by this procedure was ridiculous and coated every inch of my garage in a film of white powder. I reccommend using a respirator mask while doing this.
Once all the boards, and my garage, were hoovered off I could start gluing the ballast on top. Using a 2" household paint brush I applied a generous coat of homemade scenic cement (50/50 mix of PVA glue and water with 2 drops of washing up liquid) to small sections of each board, pouring the ballast on top while the cement was still wet. Best results came from starting at the base level and coating roughly half the area with glue then adding the ballast in quite a thick layer, approx 1/4" thick leaving an inch or so of the glue exposed at the edge where the next lot of glue and ballast would go down. Then coated the 2nd half of the base level with glue making sure to overlap onto the inch you left exposed and liberally covering with more ballast. The first level of the hill was done the same way but spreading down the hill slopes as well. The top level could be done in one hit as it has a smaller surface area to cover. All 4 hill boards were done the same way. The lowland boards were easier just doing each one a quarter at a time using the same method. Each board was balanced on a house brick on the floor so that any overruns of glue down the sides would not glue them to the floor.
The middle photo above was of a board done in a different way to what I described but was the first board I did and I found the described method to be better.
The ballast was applied using a small jar like this,
When finished they look like this,
Once it was all dry I took another 2" paint brush and gently brushed off the excess ballast back into the container. The boards now need sealing to hold down any fine dust and grit so it doesn't cause a problem when I paint it. For this I use the same scenic cement mixture as before but need it to be delivered via a fine mist spray. Woodland scenics sell a dedicated sprayer for this,
It is crap!
So I bought a cheap spray bottle from a discount shop,
This is also crap!
Both of these only manage a single jet spray not a mist and they drip all over the place. I then found this in B&Q,
This works perfectly. Pump up the pressure with the built in pump, hold the trigger and get a nice even mist no problem and no drips. Really recommend this.
Once all 6 boards had a coat of sealant they were left to dry on bricks again for 2 days and nights and are now ready for undercoating.
That's it for now. As always, questions welcome.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Looking great Andy. I bet they're getting heavy now though!
Wyrd bið ful aræd
Re: Modular gaming table
Not as heavy as you might expect actually. The cork bark is extremely light and most of the polyfilla got sanded off. Might weigh one tonight just out of curiosity
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
That is some nice looking terrain, Andy! I am looking forward to pics of Darklands skirmishes using your lovely painted models and this terrain!
- zedmeister
- Posts: 131
- Joined: Mon Feb 25, 2013 2:26 pm
- Location: Mercia, UK
- Contact:
Re: Modular gaming table
Impressive, looking forward to see how you'll paint this...
Re: Modular gaming table
Progress! But not what you might expect.
Since I don't have Ryan's basement I am fairly limited for space to store a 6' x 4' terrain table (even a modular one) therefore I had to come up with a solution. I had this plan in my head from the start and since the weather is now turning colder and I will want to put my car back in the garage overnight to escape frost and such in the mornings I have built my solution now.
My board, when assembled, is 1210mm wide by 1815mm long and at its lowest points 60mm tall.
I bought 4 lengths of stripwood, 2 of them 70mm x 10mm x 2400mm and 2 of them 70mm x 10mm x 1220mm and a length of 42mm x 42mm baton that I cut 4 70mm sections off.
I drilled 2 countersunk holes in the ends of each piece of strip wood and 2 corresponding holes in 2 sides of each piece baton, then screwed the batons to the strtip wood creating a frame the same width as my assembled board but longer so there is a gap at each end.
I then got 6 1" by 2" batons cut to 1240mm long ( sorry for mixing metric and imperial here) and 5 pieces of 4mm MDF board, 4 pieces cut to 500mm x 1220mm and 1 cut to 380mm x 1220mm. I then cut a 42mm square out of 2 of the corners on 2 of the 500mm boards. I placed the first 500mm wide board on the inside of the frame against one end and marked on the frasme where the board ended.
Using this mark I could line the batons up across the width of the frame so that where each board joined the next there would be a baton to support them. They were then drilled, countersunk and screwed to the frame. I did this with each one working towards the centre from each end.
The MDF boards were then placed inside the frame.
Then my modular terrain table went in leaving a equal gap at each end.
The gap at each end will be the dice rolling area and token storage, I have some wood effect cushion flooring that I have cut to size and glued to the MDF board in each end. The bricks you can see are pressing it down while the PVA glue sets.
The next step will be to attach 4 pulleys to my garage ceiling and a pulley on each corner of the frame then rope it all up so it can be raised up to the ceiling, out of the way, so I can get my car back in the garage. More pics will be posted of this next step soon
Since I don't have Ryan's basement I am fairly limited for space to store a 6' x 4' terrain table (even a modular one) therefore I had to come up with a solution. I had this plan in my head from the start and since the weather is now turning colder and I will want to put my car back in the garage overnight to escape frost and such in the mornings I have built my solution now.
My board, when assembled, is 1210mm wide by 1815mm long and at its lowest points 60mm tall.
I bought 4 lengths of stripwood, 2 of them 70mm x 10mm x 2400mm and 2 of them 70mm x 10mm x 1220mm and a length of 42mm x 42mm baton that I cut 4 70mm sections off.
I drilled 2 countersunk holes in the ends of each piece of strip wood and 2 corresponding holes in 2 sides of each piece baton, then screwed the batons to the strtip wood creating a frame the same width as my assembled board but longer so there is a gap at each end.
I then got 6 1" by 2" batons cut to 1240mm long ( sorry for mixing metric and imperial here) and 5 pieces of 4mm MDF board, 4 pieces cut to 500mm x 1220mm and 1 cut to 380mm x 1220mm. I then cut a 42mm square out of 2 of the corners on 2 of the 500mm boards. I placed the first 500mm wide board on the inside of the frame against one end and marked on the frasme where the board ended.
Using this mark I could line the batons up across the width of the frame so that where each board joined the next there would be a baton to support them. They were then drilled, countersunk and screwed to the frame. I did this with each one working towards the centre from each end.
The MDF boards were then placed inside the frame.
Then my modular terrain table went in leaving a equal gap at each end.
The gap at each end will be the dice rolling area and token storage, I have some wood effect cushion flooring that I have cut to size and glued to the MDF board in each end. The bricks you can see are pressing it down while the PVA glue sets.
The next step will be to attach 4 pulleys to my garage ceiling and a pulley on each corner of the frame then rope it all up so it can be raised up to the ceiling, out of the way, so I can get my car back in the garage. More pics will be posted of this next step soon
As I always say. At the end of the day.................it goes dark
- zedmeister
- Posts: 131
- Joined: Mon Feb 25, 2013 2:26 pm
- Location: Mercia, UK
- Contact:
Re: Modular gaming table
Yay more terrain updates! Nice
Also, why is it always the sliced thumb image the loads up first. Ouch!
Also, why is it always the sliced thumb image the loads up first. Ouch!
Re: Modular gaming table
This is just great - thank you for posting!
Sometimes I see these things and part of me thinks "whoa, it's so easy I could do it over the weekend!" But the other, smarter part of me says "NOPE! You couldn't!"
I admire people who do these things though. Some day, I'll maybe ascend to the ranks of such people myself
Sometimes I see these things and part of me thinks "whoa, it's so easy I could do it over the weekend!" But the other, smarter part of me says "NOPE! You couldn't!"
I admire people who do these things though. Some day, I'll maybe ascend to the ranks of such people myself
Re: Modular gaming table
I saw tutorials online for building these and thought the that it wouldn't take long, hence why I started. 6 months later and it still needs painting and flocking
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Come on Andy! Paint it! It looks awesome and very tempting to start one of my own..... Nice one.
Re: Modular gaming table
Any updates on this? Been looking forward to the finished product!
Re: Modular gaming table
Soon. Now that it has warmed up in the UK I can leave my car out of the garage and have dropped the game board back down out of the ceiling to start painting it. Have also bought a 8ltr compressor and a larger spray gun to help get it done
Once I get a family wedding out of the way this weekend I may start work on it again.
Once I get a family wedding out of the way this weekend I may start work on it again.
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Awesome, looking forward to it. The weather has finally gotten nice here also but my gf wants to build a back patio.... I'll have to wait to build my terrain but I'm going to use your process as a framework most likely.
Re: Modular gaming table
Started work again today. Not much to show but I have undercoated the boards in black.
This was done using a compressor with a spray gun attachment
I used cheap acrylic paint bought from a discount store (The Range) and mixed it 50/50 with water and sprayed it at a fairly high pressure (around 60psi)
The spray primer is not used and was just there at the time of the photo. I have used the whole bottle of black on the right to cover all the boards.
Lastly I'll show you what I have ended up using to suspend the board from the ceiling. I couldn't find any pulleys that I felt I could trust to hold the weight so I drilled a large hole through 2 of my joists and threaded a piece of angle iron, that a friend had in his garage, through them to create a support strut. I then clipped a chain block, from Amazon, to it and looped 3 cargo straps under the board and clipped them to the hook under the block. Then hoisted it up to the ceiling. You can just about see the straps I used lying on the ladders in the background
Sorry I don't have a shot of it suspended, will have to wait until its finished now
This was done using a compressor with a spray gun attachment
I used cheap acrylic paint bought from a discount store (The Range) and mixed it 50/50 with water and sprayed it at a fairly high pressure (around 60psi)
The spray primer is not used and was just there at the time of the photo. I have used the whole bottle of black on the right to cover all the boards.
Lastly I'll show you what I have ended up using to suspend the board from the ceiling. I couldn't find any pulleys that I felt I could trust to hold the weight so I drilled a large hole through 2 of my joists and threaded a piece of angle iron, that a friend had in his garage, through them to create a support strut. I then clipped a chain block, from Amazon, to it and looped 3 cargo straps under the board and clipped them to the hook under the block. Then hoisted it up to the ceiling. You can just about see the straps I used lying on the ladders in the background
Sorry I don't have a shot of it suspended, will have to wait until its finished now
As I always say. At the end of the day.................it goes dark
Re: Modular gaming table
Looking good, very creative use of an air compressor. I am anxious to see this painted up. It looks awesome with just the black primer.
Thanks!
Thanks!
Re: Modular gaming table
Unfortunately, personal circumstances mean that, I am looking to sell this board in its current state (as seen in the last set of photos). I have off-cuts of foam, lots of rocks, sand, grit and flock, as well as some paint to go with it. Everything you should need to finish it. If anyone is interested, please private message me on here.
As I always say. At the end of the day.................it goes dark
Modular gaming table
looking great I've been wanting to try something like this, since the GF probably wouldn't be thrilled at having a room of our small house nearly filled with a permanent gaming table. she's very understanding, but...there ARE limits...
1fatp8uh3k5159596
Re: Modular gaming table
This is looking great so far, cant wait to see more.
not sure if it has been mentioned but if you are in the UK looking for XPS it is used for underfloor insulation and quite a few sell it on EBAY in large sheets or packs quite cheap
not sure if it has been mentioned but if you are in the UK looking for XPS it is used for underfloor insulation and quite a few sell it on EBAY in large sheets or packs quite cheap
Who is online
Users browsing this forum: No registered users and 1 guest